Cold-Formed Steel Codes and Standards
This wiki (editable page) was created so that a large group of people could contribute to developing a list of the cold-formed steel codes and standards that are in use around the world. To aid in the development of this list Ben Schafer (schafer@jhu.edu) sent an initial email to members of the following organizations: CFSEI, SSRC TG 13, ASCE-SEI CFS, AISI-COS, AISI-COFS.
Help us now!
See how easy it is to add (or correct) the standards of your own country
1. Click "Edit Page" at the top of this page (enter the password, contact schafer@jhu.edu if you do not have it)
2. Add information about your country or a country or region you know (add your name to the bottom as a contributor)
3. Click Save!
Please add information about any country that you know information about the current cold-formed steel specifications in use below. The following divisions for countries is based on
http://en.wikipedia.org/wiki/List_of_countries, any such division is flawed to begin with, but provides a means to organize the results. Feel free to add any notes you would like as well. Some countires which are listed below were of particular interest to the initial group forming this list. Your help is much appreciated.
Africa
Ethiopia
Specification: Unknown
Building Code: Unknown
Americas
United States
Specification: North American Specification for the Design of Cold-Formed Steel Structural Members. American Iron and Steel Institute (http://tinyurl.com/yq5wzo) latest version now numbered as AISI-S100-07, 2007 version nearing final approval as of June 2007.
Building Code: International Building Code, International Code Council (http://www.iccsafe.org/) local building codes and/or NFPA may also be enforced, but the IBC is as close to a national building code as exists in the United States, both IBC and NFPA reference AISI.
Canada
Specification: S136, full details needed (http://www.csa-intl.org/onlinestore/GetCatalogItemDetails.asp?mat=000000000002415602)
Building Code: National Building Code of Canada (http://www.nationalcodes.ca/nbc/index_e.shtml)
Puerto Rico
Specification: Unknown
Building Code: Unknown - but the ICC has a Puerto Rico field office (http://www.iccsafe.org/government/international.html) so likely one can use ICC for the building code. If so, then this means the U.S. Spec. would be applicable for cold-formed steel.
Mexico
Specification: North American Specification for the Design of Cold-Formed Steel Structural Members, full details needed
Building Code: Unknown
Brazil
Specification: NBR 14762:2001 Dimensionamento de estruturas de aço constituídas por perfis formados a frio - Procedimento (Cold-formed steel design - Procedure, last update 2001) and NBR 6355:2003 Perfis estruturais de aço formados a frio - Padronização (Cold-formed steel structural profiles, last update 2003)
Building Code: ABNT - Associação Brasileira de Normas Técnicas (www.abnt.org.br)
Asia
India
Specification: Unknown
Building Code : IS 801(under revision), also model code National Building Code of India (http://www.bis.org.in/sf/nbc.htm)
China
(Added by Gaoning Wang)
Specification: Technical Code of Cold-formed Thin-wall Steel Structures
Building Code: GB 50018-2002 (current version)
Japan
Specification: Design Manual of Light-gauge Steel Structures
Building Code: Technical standard notification No.1641 concerning light-gauge steel structures
Singapore
Specification: Unknown
Building Code: Unknown
Middle East (Asia)
Europe
EU Countries
(Added by C. van Zandwijk M.Sc.)
Specification:
-
EN 1993-1-3 (same as Eurocode 3 part 1-3), Design of steel structures - Cold formed thin gauge members and sheeting
-
-
Each European country will get it's own National Annex Documents (NAD)
Finland
Specification: Unknown
Building Code: Unknown
France
Specification: Unknown
Building Code: Unknown
Germany
Specification: Unknown
Building Code: Unknown
Italy
(Added by R. Landolfo)
Specification:
UNI CNR 10022 (National Document)
EN 1993-1-3 (Not compulsory)
Building Code: Unknown
The Netherlands
(Added by C. van Zandwijk M.Sc.)
Specification:
-
NEN 6773 - Steel Structures, Basic requirements and rules for calculations of thin gauge sections. (NEN means "Nederlandse Norm")
-
All NEN codes will be replaced by Eurocodes in the next few years. Assumption: Januari 2008 introduction of Eurocode, (NEN also allowed). Januari 2010 only Eurocodes allowed
-
Alternatively use for Eurocode: NEN-EN or NEN-ENV which means "Europese Norm" (European Code) and "Europese Norm Voorlopig (pre European Code)
Building Codes:
-
NEN-EN 1993-1-1 Technical building principles for building structures (replaces NEN 6770, NEN 6771)
-
NEN-EN 1993-1-2 Determination by calculation of fire resistance of building elements (replaces NEN 6072)
-
NEN-EN 1993-1-3 Cold formed thin gauge members and sheeting (replaces NEN 6773)
-
NEN-EN 1993-1-4 Rules and requirements for stainless steels
-
NEN-EN 1993-1-5 Stiffened plating subjected to in plane loading
-
NEN-EN 1993-1-6 Strenght and stabiliy of steel shells
-
NEN-EN 1993-1-7 Stiffenend plating subjected to out plane bending
-
NEN-EN 1993-1-8 Rules and requirements for connections (replaces NEN 6772, NEN 2062)
-
NEN-EN 1993-1-9 Fatigue
-
NEN-EN 1993-1-10 Requirements for steel quality i.r.t. brittle fracture of statical loaded structures (replaces NEN 6774)
-
NEN-EN 1993-1-11 Rules and requirements for tensional loaded elements
United Kingdom
Specification: Unknown
Building Code: Unknown
Hungary
Specification: Unknown
Building Code: Unknown
Turkey
Specification: Unknown
Building Code: Unknown
Portugal
Specification: Eurocode 3 Part 1.3 (info from D. Camotim)
Building Code: Unknown
Oceania
Australia
Specification: AS/NZS 4600
AS/NZS 4600:2005 Similar to NAS 2007 but includes high strength steels such as G550 for all sections. (Greg Hancock)
Building Code: Building Code of Australia (National document) calls AS/NZS 4600:2005
NewZealand
Specification: AS/NZS 4600 (same as Australia)
Building Code: Unknown
Contributors
Ben Schafer, Johns Hopkins University, Baltimore, MD, United States (schafer@jhu.edu)
Luiz Vieira, Johns Hopkins University, Baltimore, MD, United States (luizvieirajr@gmail.com)
Cor van Zandwijk, CFP Engineering, Nieuw-Beijerland, The Netherlands (info@CFPengineering.com)
Dinar Camotim
Gregory Hancock
Raffaele Landolfo
add your name here
Comments (0)
You don't have permission to comment on this page.